Q-Logic 8C/16 Instrukcja Użytkownika Strona 136
- Strona / 222
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
A – Command Line Interface
Reset Command
A-22 59022-06 A
Q
Reset Command
Resets the switch configuration parameters. If you omit the keyword, the default is
Reset Switch.
Authority Admin
Syntax reset
config [config_name]
factory
port [port_number]
snmp
switch (default)
system
zoning
Keywords config [config_name]
Resets the configuration given by [config_name] to the factory default values for
switch, port, alarm threshold, and zoning configuration. If [config_name] does not
exist on the switch, a configuration with that name will be created. If you omit
[config_name], the active configuration is reset. You must activate the
configuration for the changes to take effect. Refer to Table A-3 through Tabl e A - 6
for switch, port, and alarm threshold configuration default values.
factory
Resets switch configuration, port configuration, alarm threshold configuration,
zoning configuration, SNMP configuration, system configuration, and zoning to
the factory default values. The switch configuration is activated automatically.
Refer to Table A-3 through Ta ble A-8.
port [port_number]
Reinitializes the port given by [port_number]. Ports are numbered beginning
with 0.
snmp
Resets the SNMP configuration settings to the factory default values. Refer to
Table A-7 for SNMP configuration default values.
switch
Resets the switch without a power-on self test. This reset disrupts traffic and
activates the pending firmware. This command also closes all management
sessions. This is the default. To reset the switch with a power-on self test, refer to
the ”Hardreset Command” on page A-12. To reset the switch without disrupting
traffic, refer to the ”Hotreset Command” on page A-15.
system
Resets the system configuration settings to the factory default values. Refer to
Table A-8 for system configuration default values.
zoning
Clears the zoning database and deactivates the active zone set. The zoning
configuration values (autosave, default visibility) remain unchanged.
- User’s Guide 1
- Document Revision History 2
- Table of Contents 3
- Section 3 Managing Fabrics 4
- Section 4 Managing Switches 5
- Section 5 Managing Ports 6
- 59022-06 A Page vii 7
- 59022-06 A Page ix 9
- Page x 59022-06 A 10
- Introduction 11
- Technical Support 12
- Availability 12
- Training 12
- Contact Information 12
- Using SANbox Manager 13
- 2 – Using SANbox Manager 14
- Installing SANbox Manager 14
- 2-2 59022-06 A 14
- 2-4 59022-06 A 16
- Starting SANbox Manager 18
- 59022-06 A 2-7 19
- Exiting SANbox Manager 20
- Uninstalling SANbox Manager 21
- 2-10 59022-06 A 22
- 59022-06 A 2-11 23
- Using Online Help 24
- SANbox Manager User Interface 25
- Menu Bar 26
- Table 2-2. Menu Shortcut Keys 27
- Tool Bar 28
- Fabric Tree 29
- Graphic Window 30
- Data Window and Tabs 30
- Working Status Indicator 30
- Using the Topology Display 31
- Switch and Link Status 31
- Selecting Switches and Links 32
- Topology Data Windows 33
- Using the Faceplate Display 34
- Port Views and Status 34
- Working with Ports 35
- Selecting Ports 35
- Faceplate Data Windows 36
- Managing Fabrics 37
- Inter-Switch Link Security 38
- Inband Management 38
- Managing the Fabric Database 39
- Adding a Fabric 39
- Removing a Fabric 40
- Opening a Fabric View File 40
- Saving a Fabric View File 40
- Rediscovering a Fabric 41
- Replacing a Failed Switch 42
- Deleting Switches and Links 43
- Displaying Fabric Information 43
- Fabric Status 43
- Displaying the Event Browser 45
- Table 3-2. Severity Levels 46
- Filtering the Event Browser 47
- Sorting the Event Browser 48
- Active Zone Set Data Window 49
- Zoning a Fabric 50
- Zoning Concepts 50
- Soft Zones 51
- Zone Sets 52
- Zoning Database 53
- Zoning Configuration 53
- FC-SW-2 Auto Save 54
- Default Visibility 54
- Restoring Default Zoning 55
- Merging Fabrics and Zoning 55
- Zone Merge Failure 55
- Zone Merge Failure Recovery 56
- Using the Edit Zoning Window 57
- Managing Zone Sets 59
- Creating a Zone Set 59
- Copying a Zone to a Zone Set 60
- Removing a Zone Set 61
- Managing Zones 62
- Creating a Zone in a Zone Set 62
- Adding Zone Members 63
- Renaming a Zone or a Zone Set 64
- Removing a Zone Member 64
- Changing Zone Types 65
- Managing Aliases 65
- Creating an Alias 65
- Adding a Member to an Alias 66
- Managing Switches 67
- Creating User Accounts 68
- Removing a User Account 69
- 4 – Managing Switches 70
- Managing User Accounts 70
- 4-4 59022-06 A 70
- Displaying Switch Information 71
- Displaying Hardware Status 72
- Switch Data Window 73
- Link Data Window 76
- 59022-06 A 4-11 77
- Configuring Alarms 78
- Sample Interval 79
- Paging a Switch 80
- Setting the Date and Time 80
- Resetting a Switch 81
- Configuring a Switch 82
- Switch Properties 82
- Symbolic Name 83
- Switch Administrative States 83
- Domain ID and Domain ID Lock 84
- Broadcast Support 85
- FC-SW-2 Compliance for Zoning 85
- Legacy Port Address Format 86
- Timeout Values 86
- Network Properties 87
- IP Configuration 88
- SNMP Configuration 89
- SNMP Trap Configuration 90
- Remote Logging 90
- Archiving a Switch 91
- Restoring a Switch 92
- 59022-06 A 4-27 93
- Managing Firmware 94
- Installing Firmware 94
- Changing the Pending Firmware 95
- 4-32 59022-06 A 98
- Managing Ports 99
- Monitoring Port Status 100
- Displaying Port Modes 100
- Displaying Port Speeds 101
- Port Statistics Data Window 102
- Port Information Data Window 105
- Name Server Data Window 106
- Configuring Ports 107
- Changing Port Speeds 109
- Changing Port Modes 109
- I/O Stream Guard 111
- Scan Device 111
- Extending Port Credits 111
- Resetting a Port 112
- Testing Ports 113
- 5 – Managing Ports 114
- 5-16 59022-06 A 114
- Command Line Interface 115
- Command Syntax 116
- Commands 117
- Admin Command 118
- Alias Command 119
- A – Command Line Interface 120
- A-6 59022-06 A 120
- Config Command 121
- A-8 59022-06 A 122
- 59022-06 A A-9 123
- Date Command 124
- Fallback Command 125
- Hardreset Command 126
- Help Command 127
- History Command 128
- Hotreset Command 129
- Image Command 130
- Lip Command 131
- Passwd Command 132
- Ping Command 133
- Ps Command 134
- Quit Command 135
- Reset Command 136
- Set Command 141
- A-28 59022-06 A 142
- Set Config Command 143
- 59022-06 A A-35 149
- A-36 59022-06 A 150
- 59022-06 A A-37 151
- Set Log Command 152
- 59022-06 A A-39 153
- A-40 59022-06 A 154
- Set Port Command 155
- Set Setup Command 156
- 59022-06 A A-45 159
- A-46 59022-06 A 160
- Show Command 161
- A-48 59022-06 A 162
- A-52 59022-06 A 166
- 59022-06 A A-53 167
- A-54 59022-06 A 168
- 59022-06 A A-55 169
- A-56 59022-06 A 170
- 59022-06 A A-57 171
- A-58 59022-06 A 172
- Show Config Command 173
- A-60 59022-06 A 174
- 59022-06 A A-61 175
- Show Log Command 176
- 59022-06 A A-63 177
- Show Perf Command 178
- 59022-06 A A-65 179
- Show Setup Command 180
- 59022-06 A A-67 181
- A-68 59022-06 A 182
- Shutdown Command 183
- Test Command 184
- Uptime Command 187
- User Command 188
- 59022-06 A A-75 189
- Whoami Command 190
- Zone Command 191
- A-78 59022-06 A 192
- 59022-06 A A-79 193
- A-80 59022-06 A 194
- Zoneset Command 195
- A-82 59022-06 A 196
- 59022-06 A A-83 197
- Zoning Command 198
- 59022-06 A A-85 199
- A-86 59022-06 A 200
- 59022-06 A A-87 201
- A-88 59022-06 A 202
- Graphing Port Performance 203
- Exiting SANsurfer Fabric View 204
- B – Graphing Port Performance 205
- 59022-06 A B-3 205
- B-4 59022-06 A 206
- Setting the Polling Frequency 207
- Displaying Graphs 207
- Customizing Graphs 208
- Printing Graphs 209
- B-8 59022-06 A 210
- Glossary 211
- Glossary-2 59022-06 A 212
- Glossary-3 59022-06 A 213
- Glossary-4 59022-06 A 214
- 59022-06 A Index-1 215
- Index-2 59022-06 A 216
- 59022-06 A Index-3 217
- Index-4 59022-06 A 218
- 59022-06 A Index-5 219
- Index-6 59022-06 A 220
- 59022-06 A Index-7 221
- Index-8 59022-06 A 222
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji